I discovered that UniFi USW-24P-250 POE network switch is based on Linux kernel 3.6.5

Subject: I discovered that UniFi USW-24P-250 POE network switch is based on Linux kernel 3.6.5

Good day from Singapore,

I discovered that UniFi USW-24P-250 POE network switch is based on Linux kernel 3.6.5 and other open source software. I had an opportunity to play with this UniFi USW-24P-250 POE network switch recently. The console output and other information below shows that UniFi USW-24P-250 POE network switch is based on Linux kernel 3.6.5.

Please DO NOT try to configure UniFi network switches using the CLI. It WILL NOT work. If you configure UniFi network switches using the CLI, the IP address that you have manually configured will always go back to 192.168.1.20, which is the default IP address.

The only way to configure UniFi network switches is to connect them to a network environment with DHCP server. You can then install and use UniFi Controller to adopt the UniFi network switch. Configuring UniFi network switches using UniFi Controller (GUI) is extremely easy and straight forward. There is no need to use the CLI at all.

How to Configure UniFi USW-24P-250 POE Network Switch using CLI

===============================================================

Putty Settings

==============

Connection > Serial:

Speed(baud): 115200

Data bits: 8

Stop bits: 1

Parity: None

Flow control: None

Session:

Serial

Serial line: COM1

Speed: 115200

Default username and password to login to UniFi switch

======================================================

Default login: ubnt

Default password: ubnt

How to enter CLI of UniFi switch

================================

telnet localhost

enable

show run

===Begin of Default switch configuration===

!Current Configuration:

!System Description "USW-24P-250, 5.11.0.11599, Linux 3.6.5"

!System Software Version "5.11.0.11599"

!System Up Time "0 days 0 hrs 24 mins 4 secs"

!Additional Packages QOS,IPv6 Management

network parms 0.0.0.0 0.0.0.0 0.0.0.0

vlan database

exit

configure

line console

exit

line telnet

exit

spanning-tree mode rstp

no snmp-server community "public"

no snmp-server community "private"

set igmp reportforward lldp

set mld reportforward lldp

ip dhcp snooping

ip dhcp snooping vlan 1

cos-queue min-bandwidth 0 10 10 10 10 0 0 0

keepalive

interface 0/1

description 'Port 1'

vlan ingressfilter

port-security max-dynamic 0

lldp transmit

lldp receive

lldp transmit-tlv port-desc

lldp transmit-tlv sys-name

lldp transmit-tlv sys-desc

lldp transmit-tlv sys-cap

lldp med

exit

interface 0/2

description 'Port 2'

vlan ingressfilter

port-security max-dynamic 0

lldp transmit

lldp receive

lldp transmit-tlv port-desc

lldp transmit-tlv sys-name

lldp transmit-tlv sys-desc

lldp transmit-tlv sys-cap

lldp med

exit

interface 0/3

description 'Port 3'

vlan ingressfilter

port-security max-dynamic 0

lldp transmit

lldp receive

lldp transmit-tlv port-desc

lldp transmit-tlv sys-name

lldp transmit-tlv sys-desc

lldp transmit-tlv sys-cap

lldp med

exit

interface 0/4

description 'Port 4'

vlan ingressfilter

port-security max-dynamic 0

lldp transmit

lldp receive

lldp transmit-tlv port-desc

lldp transmit-tlv sys-name

lldp transmit-tlv sys-desc

lldp transmit-tlv sys-cap

lldp med

exit

interface 0/5

description 'Port 5'

vlan ingressfilter

port-security max-dynamic 0

lldp transmit

lldp receive

lldp transmit-tlv port-desc

lldp transmit-tlv sys-name

lldp transmit-tlv sys-desc

lldp transmit-tlv sys-cap

lldp med

exit

interface 0/6

description 'Port 6'

vlan ingressfilter

port-security max-dynamic 0

lldp transmit

lldp receive

lldp transmit-tlv port-desc

lldp transmit-tlv sys-name

lldp transmit-tlv sys-desc

lldp transmit-tlv sys-cap

lldp med

exit

interface 0/7

description 'Port 7'

vlan ingressfilter

port-security max-dynamic 0

lldp transmit

lldp receive

lldp transmit-tlv port-desc

lldp transmit-tlv sys-name

lldp transmit-tlv sys-desc

lldp transmit-tlv sys-cap

lldp med

exit

interface 0/8

description 'Port 8'

vlan ingressfilter

port-security max-dynamic 0

lldp transmit

lldp receive

lldp transmit-tlv port-desc

lldp transmit-tlv sys-name

lldp transmit-tlv sys-desc

lldp transmit-tlv sys-cap

lldp med

exit

interface 0/9

description 'Port 9'

vlan ingressfilter

port-security max-dynamic 0

lldp transmit

lldp receive

lldp transmit-tlv port-desc

lldp transmit-tlv sys-name

lldp transmit-tlv sys-desc

lldp transmit-tlv sys-cap

lldp med

exit

interface 0/10

description 'Port 10'

vlan ingressfilter

port-security max-dynamic 0

lldp transmit

lldp receive

lldp transmit-tlv port-desc

lldp transmit-tlv sys-name

lldp transmit-tlv sys-desc

lldp transmit-tlv sys-cap

lldp med

exit

interface 0/11

description 'Port 11'

vlan ingressfilter

port-security max-dynamic 0

lldp transmit

lldp receive

lldp transmit-tlv port-desc

lldp transmit-tlv sys-name

lldp transmit-tlv sys-desc

lldp transmit-tlv sys-cap

lldp med

exit

interface 0/12

description 'Port 12'

vlan ingressfilter

port-security max-dynamic 0

lldp transmit

lldp receive

lldp transmit-tlv port-desc

lldp transmit-tlv sys-name

lldp transmit-tlv sys-desc

lldp transmit-tlv sys-cap

lldp med

exit

interface 0/13

description 'Port 13'

vlan ingressfilter

port-security max-dynamic 0

lldp transmit

lldp receive

lldp transmit-tlv port-desc

lldp transmit-tlv sys-name

lldp transmit-tlv sys-desc

lldp transmit-tlv sys-cap

lldp med

exit

interface 0/14

description 'Port 14'

vlan ingressfilter

port-security max-dynamic 0

lldp transmit

lldp receive

lldp transmit-tlv port-desc

lldp transmit-tlv sys-name

lldp transmit-tlv sys-desc

lldp transmit-tlv sys-cap

lldp med

exit

interface 0/15

description 'Port 15'

vlan ingressfilter

port-security max-dynamic 0

lldp transmit

lldp receive

lldp transmit-tlv port-desc

lldp transmit-tlv sys-name

lldp transmit-tlv sys-desc

lldp transmit-tlv sys-cap

lldp med

exit

interface 0/16

description 'Port 16'

vlan ingressfilter

port-security max-dynamic 0

lldp transmit

lldp receive

lldp transmit-tlv port-desc

lldp transmit-tlv sys-name

lldp transmit-tlv sys-desc

lldp transmit-tlv sys-cap

lldp med

exit

interface 0/17

description 'Port 17'

vlan ingressfilter

port-security max-dynamic 0

lldp transmit

lldp receive

lldp transmit-tlv port-desc

lldp transmit-tlv sys-name

lldp transmit-tlv sys-desc

lldp transmit-tlv sys-cap

lldp med

exit

interface 0/18

description 'Port 18'

vlan ingressfilter

port-security max-dynamic 0

lldp transmit

lldp receive

lldp transmit-tlv port-desc

lldp transmit-tlv sys-name

lldp transmit-tlv sys-desc

lldp transmit-tlv sys-cap

lldp med

exit

interface 0/19

description 'Port 19'

vlan ingressfilter

port-security max-dynamic 0

lldp transmit

lldp receive

lldp transmit-tlv port-desc

lldp transmit-tlv sys-name

lldp transmit-tlv sys-desc

lldp transmit-tlv sys-cap

lldp med

exit

interface 0/20

description 'Port 20'

vlan ingressfilter

port-security max-dynamic 0

lldp transmit

lldp receive

lldp transmit-tlv port-desc

lldp transmit-tlv sys-name

lldp transmit-tlv sys-desc

lldp transmit-tlv sys-cap

lldp med

exit

interface 0/21

description 'Port 21'

vlan ingressfilter

port-security max-dynamic 0

lldp transmit

lldp receive

lldp transmit-tlv port-desc

lldp transmit-tlv sys-name

lldp transmit-tlv sys-desc

lldp transmit-tlv sys-cap

lldp med

exit

interface 0/22

description 'Port 22'

vlan ingressfilter

port-security max-dynamic 0

lldp transmit

lldp receive

lldp transmit-tlv port-desc

lldp transmit-tlv sys-name

lldp transmit-tlv sys-desc

lldp transmit-tlv sys-cap

lldp med

exit

interface 0/23

description 'Port 23'

vlan ingressfilter

port-security max-dynamic 0

lldp transmit

lldp receive

lldp transmit-tlv port-desc

lldp transmit-tlv sys-name

lldp transmit-tlv sys-desc

lldp transmit-tlv sys-cap

lldp med

exit

interface 0/24

description 'Port 24'

vlan ingressfilter

port-security max-dynamic 0

lldp transmit

lldp receive

lldp transmit-tlv port-desc

lldp transmit-tlv sys-name

lldp transmit-tlv sys-desc

lldp transmit-tlv sys-cap

lldp med

exit

interface 0/25

description 'Port 25'

vlan ingressfilter

port-security max-dynamic 0

lldp transmit

lldp receive

lldp transmit-tlv port-desc

lldp transmit-tlv sys-name

lldp transmit-tlv sys-desc

lldp transmit-tlv sys-cap

lldp med

exit

interface 0/26

description 'Port 26'

vlan ingressfilter

port-security max-dynamic 0

lldp transmit

lldp receive

lldp transmit-tlv port-desc

lldp transmit-tlv sys-name

lldp transmit-tlv sys-desc

lldp transmit-tlv sys-cap

lldp med

exit

interface lag 1

shutdown

no port-channel static

vlan participation exclude 1

exit

interface lag 2

shutdown

no port-channel static

vlan participation exclude 1

exit

interface lag 3

shutdown

no port-channel static

vlan participation exclude 1

exit

interface lag 4

shutdown

no port-channel static

vlan participation exclude 1

exit

interface lag 5

shutdown

no port-channel static

vlan participation exclude 1

exit

interface lag 6

shutdown

no port-channel static

vlan participation exclude 1

exit

no errdisable recovery cause mac-locking

no errdisable recovery cause denial-of-service

exit

===End of default switch configuration===

show network

Interface Status............................... Up

IP Address..................................... 0.0.0.0

Subnet Mask.................................... 0.0.0.0

Default Gateway................................ 0.0.0.0

IPv6 Administrative Mode....................... Enabled

IPv6 Prefix is ................................ fe80::f692:bfff:fe71:aac7/64

Burned In MAC Address.......................... F4:92:BF:71:AA:C7

Locally Administered MAC address............... 00:00:00:00:00:00

MAC Address Type............................... Burned In

Configured IPv4 Protocol....................... None

Configured IPv6 Protocol....................... None

IPv6 AutoConfig Mode........................... Enabled

Management VLAN ID............................. 1

Reference Guide: Getting into the CLI for a Unifi switch

Link: https://dan.langille.org/2018/01/12/getting-into-the-cli-for-a-unifi-switch/

Reference Guide: Ubiquiti Networks EdgeSwitch CLI Command Reference

Link: https://www.doubleradius.com/site/stores/ubiquiti/Ubiquiti-Edgeswitch-CLI-Command-Reference-Quick-Start-Guide.pdf

Configure the management interface of UniFi switch

==================================================

hostname UniFi-USW-24P-250-Switch

network parms 192.168.0.6 255.255.255.0 192.168.0.2

(UniFi-USW-24P-250-Switch) #show network

Interface Status............................... Up

IP Address..................................... 192.168.0.6

Subnet Mask.................................... 255.255.255.0

Default Gateway................................ 192.168.0.2

IPv6 Administrative Mode....................... Enabled

IPv6 Prefix is ................................ fe80::f692:bfff:fe71:aac7/64

Burned In MAC Address.......................... F4:92:BF:71:AA:C7

Locally Administered MAC address............... 00:00:00:00:00:00

MAC Address Type............................... Burned In

Configured IPv4 Protocol....................... None

Configured IPv6 Protocol....................... None

IPv6 AutoConfig Mode........................... Enabled

Management VLAN ID............................. 1

configure

username admin level 15 password

Enter new password:****************

Confirm new password:****************

write memory

This operation may take a few minutes.

Management interfaces will not be available during this time.

Are you sure you want to save? (y/n) y

Config file 'startup-config' created successfully .

Configuration Saved!

UBNT-US.v5.11.0# reboot now

UBNT-US.v5.11.0# + exec

umount: can't remount rootfs read-only

The system is going down NOW!

Sent SIGTERM to all processes

Sent SIGKILL to[ 991.180000] Disabling non-boot CPUs ...

[ 991.180000] Restarting system.

U-Boot usw-v1.1.4.115-g14af1ee6 (Feb 14 2017 - 18:50:54)

DEV ID= 0000db56

SKU ID = 0x8344

DDR type: DDR3

MEMC 0 DDR speed = 667MHz

Validate Shmoo parameters stored in flash ..... OK

Press Ctrl-C to run Shmoo ..... skipped

Restoring Shmoo parameters from flash ..... done

Running simple memory test ..... OK

DDR Tune Completed

DRAM: 256 MiB

WARNING: Caches not enabled

soc_pcie_hw_init : port->reg_base = 0x18012000 , its value = 0x1

PCIe port 0 in RC mode

pos is 172

==>PCIE: LINKSTA reg 0xbe val 0x1001

**************

port 0 is not active!!

**************

In: serial

Out: serial

Err: serial

Unlocking L2 Cache ...Done

arm_clk=400MHz, axi_clk=200MHz, apb_clk=50MHz, arm_periph_clk=200MHz

Disabling outer cache

Net: Board Net Initialization Failed

No ethernet found.

Hit any key to stop autoboot: 0

ubnt_bootsel_init: bootsel magic=a34de82b, bootsel = 0

UBNT application initialized

Boot partition selected = 0

Loading Kernel Image @ 1000000, size = 15728640

Verifying 'kernel0' parition:OK

## Booting kernel from Legacy Image at 01000000 ...

Image Name: Ubiquiti 5.11.0.11599

Image Type: ARM Linux Kernel Image (uncompressed)

Data Size: 15068480 Bytes = 14.4 MiB

Load Address: 00018000

Entry Point: 00018000

Verifying Checksum ... OK

Loading Kernel Image ... OK

boot_prep_linux commandline: console=ttyS0,115200 mem=128M@0x0 mem=128M@0x68000000 mtdparts=spi1.0:768k(u-boot),64k(u-boot-env),64k(shmoo),15360k(kernel0),15424k(kernel1),1024k(cfg),64k(EEPROM) ubntbootid=0

Starting kernel ...

Disabling outer cache

[ 0.000000] Booting Linux on physical CPU 0

[ 0.000000] Linux version 3.6.5 (builder@link-owrt1505-builder) (gcc version 4.7.2 (OpenWrt GCC 4.7.2 unknown) ) #2 SMP Wed Apr 22 10:09:32 MDT 2020

[ 0.000000] CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c53c7d

[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache

[ 0.000000] Machine: Broadcom iProc

[ 0.000000] Memory policy: ECC disabled, Data cache writealloc

[ 0.000000] BUG: mapping for 0x18000000 at 0xf0000000 out of vmalloc space

[ 0.000000] BUG: mapping for 0x19000000 at 0xf1000000 out of vmalloc space

[ 0.000000] PERCPU: Embedded 7 pages/cpu @c1caf000 s6272 r8192 d14208 u32768

[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 61952

[ 0.000000] Kernel command line: console=ttyS0,115200 mem=128M@0x0 mem=128M@0x68000000 mtdparts=spi1.0:768k(u-boot),64k(u-boot-env),64k(shmoo),15360k(kernel0),15424k(kernel1),1024k(cfg),64k(EEPROM) ubntbootid=0 ubootver=usw-v1.1.4.115-g14af1ee6

[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)

[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)

[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)

[ 0.000000] Memory: 128MB 128MB = 256MB total

[ 0.000000] Memory: 244992k/244992k available, 17152k reserved, 131072K highmem

[ 0.000000] Virtual kernel memory layout:

[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)

[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)

[ 0.000000] vmalloc : 0xc8800000 - 0xf0000000 ( 632 MB)

[ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB)

[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)

[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)

[ 0.000000] .text : 0xc0018000 - 0xc034d7f8 (3286 kB)

[ 0.000000] .init : 0xc034e000 - 0xc0e4c880 (11259 kB)

[ 0.000000] .data : 0xc0e4e000 - 0xc0e76d40 ( 164 kB)

[ 0.000000] .bss : 0xc0e76d64 - 0xc0ea5354 ( 186 kB)

[ 0.000000] SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1

[ 0.000000] Hierarchical RCU implementation.

[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1.

[ 0.000000] NR_IRQS:292

[ 0.000000] sched_clock: 32 bits at 100 Hz, resolution 10000000ns, wraps every 4294967286ms

[ 0.010000] Calibrating delay loop... 795.44 BogoMIPS (lpj=3977216)

[ 0.050000] pid_max: default: 4096 minimum: 301

[ 0.050000] Mount-cache hash table entries: 512

[ 0.050000] CPU: Testing write buffer coherency: ok

[ 0.050000] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000

[ 0.050000] Setting up static identity map for 0x282350 - 0x2823a8

[ 0.050000] L310 cache controller enabled

[ 0.050000] l2x0: 8 ways, CACHE_ID 0x410000c9, AUX_CTRL 0x0a120000, Cache size: 131072 B

[ 0.050000] Brought up 1 CPUs

[ 0.050000] SMP: Total of 1 processors activated (795.44 BogoMIPS).

[ 0.050000] devtmpfs: initialized

[ 0.060000] NET: Registered protocol family 16

[ 0.060000] DMA: preallocated 256 KiB pool for atomic coherent allocations

[ 0.060000] GENPLL[5] mdiv=40 rate=2000000000

[ 0.060000] Sel=1 Ovr=1 Div=48

[ 0.060000] UART clock rate 50000000

[ 0.080000] bio: create slab <bio-0> at 0

[ 0.080000] Bluetooth: Core ver 2.16

[ 0.080000] NET: Registered protocol family 31

[ 0.080000] Bluetooth: HCI device and connection manager initialized

[ 0.080000] Bluetooth: HCI socket layer initialized

[ 0.080000] Bluetooth: L2CAP socket layer initialized

[ 0.080000] Bluetooth: SCO socket layer initialized

[ 0.080000] Switching to clocksource iproc_gtimer

[ 0.090000] NET: Registered protocol family 2

[ 0.090000] TCP established hash table entries: 4096 (order: 3, 32768 bytes)

[ 0.090000] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)

[ 0.090000] TCP: Hash tables configured (established 4096 bind 4096)

[ 0.090000] TCP: reno registered

[ 0.090000] UDP hash table entries: 128 (order: 0, 4096 bytes)

[ 0.090000] UDP-Lite hash table entries: 128 (order: 0, 4096 bytes)

[ 0.090000] NET: Registered protocol family 1

[ 14.360000] pm_init: Initializing Power Management ....

[ 14.360000] iproc gpiochip add GPIOA

[ 14.360000] GPIOA:ioaddr f0000060

[ 14.360000] GPIOA:intr_ioaddr f0000000 dmu_ioaddr (null)

[ 14.610000] PCIE0: LINKSTA reg 0xbe val 0x1001

[ 14.610000] reg[0xac]=0x10, reg[0xae]=0x42, reg[0xb0]=0x8000, reg[0xb4]=0x2c10, reg[0xb6]=0x10, reg[0xb8]=0x5c12, reg[0xba]=0x65, reg[0xbe]=0x1001, reg[0xc6]=0x40, reg[0xca]=0x1, reg[0xd0]=0x1f, reg[0xd2]=0x8, reg[0xdc]=0x1, PCIE0 link=0

[ 14.860000] PCIe port 1 in End-Point mode - ignored

[ 14.860000] Registering iproc_pmu_device

[ 14.860000] bounce pool size: 64 pages

[ 14.880000] squashfs: version 4.0 (2009/01/31) Phillip Lougher

[ 14.880000] msgmni has been set to 222

[ 14.880000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)

[ 14.880000] io scheduler noop registered

[ 14.880000] io scheduler deadline registered (default)

[ 14.880000] io scheduler cfq registered

[ 14.880000] Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled

[ 14.890000] serial8250.0: ttyS0 at MMIO 0x18000400 (irq = 123) is a 16550A

[ 15.360000] console [ttyS0] enabled

[ 15.370000] serial8250.0: ttyS1 at MMIO 0x18000300 (irq = 123) is a 16550A

[ 15.400000] brd: module loaded

[ 15.410000] loop: module loaded

[ 15.420000] nbd: registered device at major 43

[ 15.440000] tun: Universal TUN/TAP device driver, 1.6

[ 15.450000] Bluetooth: HCI UART driver ver 2.2

[ 15.460000] Bluetooth: HCI H4 protocol initialized

[ 15.460000] Bluetooth: HCI BCSP protocol initialized

[ 15.470000] TCP: cubic registered

[ 15.470000] NET: Registered protocol family 10

[ 15.480000] sit: IPv6 over IPv4 tunneling driver

[ 15.490000] NET: Registered protocol family 17

[ 15.490000] Bluetooth: RFCOMM TTY layer initialized

[ 15.500000] Bluetooth: RFCOMM socket layer initialized

[ 15.500000] Bluetooth: RFCOMM ver 1.11

[ 15.510000] Bluetooth: BNEP (Ethernet Emulation) ver 1.3

[ 15.510000] Bluetooth: BNEP filters: protocol multicast

[ 15.520000] Bluetooth: HIDP (Human Interface Emulation) ver 1.2

[ 15.520000] 8021q: 802.1Q VLAN Support v1.8

[ 15.530000] GENPLL[5] mdiv=40 rate=2000000000

[ 15.530000] qspi_iproc qspi_iproc.1: 1-lane output, 3-byte address

[ 15.540000] m25p80 spi1.0: found mx25l25635e, expected m25p80

[ 15.550000] m25p80 spi1.0: mx25l25635e (32768 Kbytes)

[ 15.550000] 7 cmdlinepart partitions found on MTD device spi1.0

[ 15.560000] Creating 7 MTD partitions on "spi1.0":

[ 15.560000] 0x000000000000-0x0000000c0000 : "u-boot"

[ 15.570000] 0x0000000c0000-0x0000000d0000 : "u-boot-env"

[ 15.580000] 0x0000000d0000-0x0000000e0000 : "shmoo"

[ 15.580000] 0x0000000e0000-0x000000fe0000 : "kernel0"

[ 15.590000] 0x000000fe0000-0x000001ef0000 : "kernel1"

[ 15.600000] 0x000001ef0000-0x000001ff0000 : "cfg"

[ 15.610000] 0x000001ff0000-0x000002000000 : "EEPROM"

[ 15.640000] Freeing init memory: 11256K

[ 15.700000] ubnt_common: module license 'Proprietary' taints kernel.

[ 15.710000] Disabling lock debugging due to kernel taint

[ 15.780000] Data abort at addr=0xc8a10224, fsr=0x1406 ignored.

[ 15.790000] Data abort at addr=0xc8a10224, fsr=0x1406 ignored.

[ 15.810000] gpiodev: reset_timeout=3

Could not find cfg type: 1

Could not find cfg type: 2

...running /sbin/init

init started: BusyBox v1.23.2 (2020-04-22 10:04:15 MDT)

+ exec

Restoring EEPROM data from ubnthal

MAC: f4:92:bf:71:aa:c7

Validating the active image /dev/mtd3..."5.11.0.11599"

Validating the backup image /dev/mtd4..."5.11.0.11599"

DMA pool size: 4194304

AXI unit 0: Dev 0x8344, Rev 0x01, Chip BCM53344_A0, Driver BCM56150_A0

SOC unit 0 attached to PCI device BCM53344_A0

(Unit 1)>

Applying Global configuration, please wait ...

Applying Interface configuration, please wait ...

Please press Enter to activate this console. inform sent

inform sent

Using the UniFi Controller to adopt the UniFi Switch

=====================================================

192.168.0.10 is the UniFi Controller on the management laptop.

UBNT-US.v5.11.0# set-inform http://192.168.0.10:8080/inform

Adoption request sent to 'http://192.168.0.10:8080/inform'. Use the controller to complete the adopt process.

telnet localhost

enable

network parms 192.168.0.6 255.255.255.0 192.168.0.2

UBNT-US.v5.11.0# info

Model: USW-24P-250

Version: 5.11.0.11599

MAC Address: f4:92:bf:71:aa:c7

IP Address: 192.168.1.20

Hostname: UBNT

Uptime: 7868 seconds

Status: Connected (http://192.168.0.10:8080/inform)

Mr. Turritopsis Dohrnii Teo En Ming, 43 years old as of 28 July 2021, is a TARGETED INDIVIDUAL living in Singapore. He is an IT Consultant with a System Integrator (SI)/computer firm in Singapore. He is an IT enthusiast.

REFERENCES

==========

[1] https://lore.kernel.org/backports/16a0622f8bfd75e0e4da3a105eca9f12@teo-en-ming-corp.com/

[2] https://lore.kernel.org/ceph-devel/d610e461c6de6b5534a52e26c7d31171@teo-en-ming-corp.com/

[3] https://lore.kernel.org/dash/f3b10b08833b7ec10a189f4062be45a7@teo-en-ming-corp.com/

[4] https://lore.kernel.org/dmaengine/0a9534bca5051fc844f1c42d683af085@teo-en-ming-corp.com/

[5] https://lore.kernel.org/dwarves/7134c5776569664b145d2bda99b7c710@teo-en-ming-corp.com/